10 x 2ml / 0.07 fl oz
Anti-aging skin filling treatment, with repairing and redensifying active ingredients of the dermal matrix that in turn offers protection against external aggressions.
It is specifically formulated for being introduced by electroporation with extremely high concentrations of the latest generation active ingredients, enhanced with the most advanced delivery and delivery systems.
10 ampoules x 2 ml.
1 ampoule / session.
Information and instructions for use.
Clean the area to be treated using a cleaning product (micellar water, cleansing milk ...) and it later can be supplemented with a tonic.
If micropuncture is applied in any area, it can be disinfected with alcohol or chlorhexidine.
It´s recommended to reduce the thickness of the CS (stratum corneum) as far as possible to facilitate the introduction of active ingredients by electroporation.
We can do it by applying a mild AHA peel or an enzymatic peel.
In medical centers you can combine it with the application of microneedling at 0.25 in localized areas.
In case its not possible to do this step, product may be introduced but it will require a longer application time to achieve their complete introduction.
Shake the ampoule until its homogenization is complete. Once it has been homogenized, make sure that no product remains on top of the ampoule. You can remove it with small strokes with your finger on the top.
Place the dropper in the ampoule up to the neck and use it to break the top. It should break with a clean sound. Discard the top of the ampoule.
Push the dropper into the ampoule with force until it is fitted.
Turn the ampoule upside down and shake so that the product goes down into the dropper. You can apply a light pressure with your fingers on the dropper to suck up the content of ampoule and facilitate the transfer of the product.
Connect the electroporation device and select the treatment to be performed and setting the time or parameters that you want to use at beginning. In the case of working with Mesolux device, we recommend always using phototherapy in active mode since it acts in synergy, enhancing the result of the treatment.
We recommend planning the area where we want to introduce the product in order to measure the amount to be introduced in each part proportionally. The result will depend on the amount of product introduced in that area, so try to introduce more product in the areas where you want a better result.
The drop application is advisable for its introduction. In this way, remove the cap and apply 2-3 drops of the product on area to be treated, introduce it immediately with the electroporation device by means of small movements on the area, adding more successively until the desired amount of product is introduced.
As we have seen previously, we will introduce the product by electroporation through small movements over the same area until we introduce the desired amount.
After introducing the product in the areas where we want a better result, it may be interesting to keep treating the rest of the area not treated in a general way. For this purpose, you can leave a part of the product (25-50%) and apply it directly or if you find that it is introduced too easily and does not allow you to cover the entire area, you can mix it with Mesogel with PDC (dynamic particle control) to have greater volume and to be able to extend the area and / or treatment time.
If you wish, you can remove the excipient that may remain on the skin. You can apply a tonic.
In this step you can finish the treatment in different ways, with the application of a cream, a mask, a facial veil, etc., to give the skin the final ending. Keep in mind that Mesoactives is an ultra-concentrated product that once introduced will not give any type of surface on the skin, so it is advisable to finish the treatment with a product adapted to the client's needs.
You can complement the treatment with products for home use.
The application of techniques such as radiofrequency or laser for 24 hours from the introduction of Mesoactives is totally discouraged, as it could damage the active ingredients and reduce the results.
Depending on the patient, the result will be visible approximately from the first session, but the final result can be seen after the course of the sessions.
We recommend taking photos to document the treatment progress to compare pre-post session and between sessions.
Skin Volumizer is formulated for an intensive filling treatment with hyaluronic acid of different molecular weights, enhanced by a significant redensification and repair of the dermal matrix through the combination of growth factors with stem cells.
On the other hand, it offers a very high protection against external aggressions and prevents the appearance of new wrinkles.
The world's first line product specifically formulated for introduction by transdermal electroporation.
The introduction by electroporation achieves that the active ingredients penetrate the entire treated tissue, allowing the safe use of concentrations much higher than those used in topical or injectable products.
The specific formulation of electroporation allows the active ingredients to move freedly, allowing their introduction until reaching the target cells, achieving maximum efficiency in the different treatments.
Main active ingredients
Biotechnological plant stem cells of marine origin that produce powerful skin regeneration. They have main action in the dermo-epidermal junction, achieving an increase in the production of elastin, collagen and enhancing epidermal renewal.
Ergothionein is an amino acid considered as a super antioxidant that also has anti-inflammatory properties, thus helping to prevent and intensively combat oxidative stress and avoiding the appearance of fine lines, wrinkles or flaccidity.
Low molecular weight hyaluronic acid (<500 Da). It reduces wrinkles and enhances the elasticity of the skin. It produces effects at the epidermal and dermal levels by stimulating the endogenic production of high molecular weight hyaluronic, thus increasing the volume of the skin, increasing the production of collagen and elastin and stimulating correct skin vascularization.
Nicotiana benthamiana Sh-Polypeptide-45 is a growth factor composed of a single recombinant peptide chain composed of a maximum of 144 amino acids. The starting gene is a synthetic copy of the human gene encoding the granulocyte macrophage colony stimulating factor.
Hyaluronic acid is a glycosaminoglycan capable of absorbing water up to 10,000 times its volume. It is an essential part of the extracellular matrix, retaining water structurally in the skin.